July 2019#

Volume	Part	Section	Change type	Description of change
1	4	3.2.3-1	Deletion	Content on implementation of internet-enabled video cameras (web cameras) removed from Vol 1 Part 4.
	10	5.7-1	Deletion	Clause 5 Sight distance requirements deleted as this content has been included in Austroads Guide to traffic management.
		10.2-1	New	New content on implementation of internet-enabled video cameras added
3	1	1, 2	Editorial	Replaced text with appropriate abbreviations.
		2	Editorial	Harmonized language with content in TRUM Volume 3 Part 2 to 4.
	2.1	All	Editorial	Simplified language where appropriate to improve consistency and readability.
		1.1	Administrative	Amended list to align with referenced content from other TRUM parts.
		1.2	Administrative	Amended point b) to allow for alternative plastic materials. Added point e) to align with content in MRTS45.
		1.2.1, 1.3	Administrative	Amended to align with content in MRTS45.
	2.2	All	Editorial	Amended reference to relevant MUTCD/AS1742 parts to include "For more information". Simplified language where appropriate to improve consistency and readability.

Section	Change type	Description of change
2.2	Administrative	Removed reference to Section 5.3.2.4 of MUTCD Part 2 as it is considered design guidance.
2.2.2	Administrative	Amended references to line marking types for consistency. Removed information regarding the legal authority of barrier lines. Added references to other relevant sections of TRUM.
2.2.3	Administrative	Removed reference to Section 5.3.4 of MUTCD Part 2 as it is considered design guidance. Added "Lane lines are used to separate lanes of traffic moving in the same direction".
2.2.4	Administrative	Aligned content with content in the MUTCD Part 2. Removed information regarding edge line influence on vehicle behavior. Added references to other relevant sections of TRUM.
2.2.6	Administrative	Removed reference to Section 5.3.7 of MUTCD Part 2 as it is considered design guidance. Removed option for a width of 80mm for turn lines.
2.2.7	Administrative	Removed reference to Section 5.3.7 of MUTCD Part 2 as it is considered design guidance. Added "Outline markings of splays, medians, islands, safety bars and shoulders shall be a single continuous line".
2.2.8	Administrative	Added section with content from MUTCD Part 2 for longitudinal lines at intersections.
2.2.9	Administrative	Added section with content from TN155 Wide Centreline Treatments.
2.3.1	Administrative	Figure 2.3.1: Removed information regarding the legal authority of stop lines. Updated figure notes.
2.3.2	Administrative	Updated references to source document. Updated figure and contents to align with harmonized MUTCD Part 10.
2.4.1	Administrative	Updated content to align with MUTCD Part 2. Added "Line marking widths for edge lines, outline markings shall be as per MUTCD Part 2 Figure 5.1".
2.4.2.1	Administrative	Removed information regarding the legal authority of pavement arrows.
2.4.2.1.2	Administrative	Moved "Entrance ramp nose marking chevrons to be reversed. See Fig. 3.3 and 3.4" to below the MUTCD Part 2 content box.
2.4.2.2	Administrative	Amended distortion ratio from10:1 to 8:1 to align with MUCTD part 2. Removed "with the word 'ONLY' between arrows if necessary" as this is not representative of Queensland practice.
2.4.2.2.1	Administrative	Replaced reference to Figure B2.18 with "displayed in the second line, as shown in Figure 2.4.2.2.5".
2.4.2.2.2	Administrative	Updated content to align with MUTCD Part 4 Added "Numerals are to be painted as per MUTCD Part 2 Figure 5.7".
2.4.2.2.3	Administrative	Updated content and figures to align with AS1742.9.
2.4.2.2.4	Administrative	Updated content and figures to align with AS1742.9 with amendments from MUTCD part 9.
2.4.2.2.6	Administrative	Updated content and figures to align with AS1742.12.
2.4.2.3	Administrative	Updated the definition of an intersection to align with the Queensland Road Rules. Added "transverse" to "recommended line width". Removed "Where the lines are not installed, the outer edges of the marking indicate the limits of the prohibition".
2.4.2.4	Administrative	Updated content and figures to align with AS1742.10.
2.4.2.6	Administrative	Updated figures to align with AS1742.10 and AS1742.13.
2.4.3.1	Administrative	Updated content and figures to align with AS1742.11.
2.4.3.2	Administrative	Updated content and figures to align with AS1742.11.
2.4.3.3	Administrative	Updated content and figures to align with AS1742.11.
2.4.3.4, Figure 2.4.3.4	Administrative	Added "pavement" to "diagonal markings". Figure 2.4.3.4, added "Diagonal markings shall be installed in accordance with MUTCD Part 2 Figure 5.5".
2.4.5	Administrative	Replaced "9 m line/3 m gap, 80 mm wide" with "to be special purpose lane lines with a reduced width of 80mm".
2.5	Administrative	Updated content and figures to align with MUTCD Part 2.
2.5.4	Administrative	Replaced "or painted with retroreflective paint " with "compliant with AS1906.3".
2.5.6	Administrative	Added section with content from MRTS45 Road Surface Delineation.
2.3	All	Editorial	Amended reference to relevant MUTCD/AS1742 parts to include "For more information". Simplified language where appropriate to improve consistency and readability.
3.3.2	Administrative	Removed reference Table 5.1 of MUTCD Part 2 as it is considered design guidance.
3.3.3	Administrative	Removed "Typical markings and signing at a substandard horizontal curve with a large speed deficiency are shown in MUTCD Part 2 Table 5.2". Removed reference Table 5.2 of MUTCD Part 2 as it is considered design guidance.
3.4.5	Administrative	Replaced "U-turn" with "turning maneuver".
3.5	Administrative	Updated content and figures to align with MUTCD Part 2.
3.7.2	Administrative	Updated content and figures to align with AS1742.12.
3.8	Administrative	Updated content and figures to align with AS1742.9. Updated extracts from TC1769 to align with most recent version.
3.9	Administrative	Change title to "Treatment to Approaches to obstructions and structures". Amended references to Tables in TRUM.
3.10	Administrative	Updated content and figures to align with AS1742.7. Updated references to other standards and figures.
3.13.2	Editorial	Updated references to other standards and figures.
3.13.3	Editorial	Updated references to other standards and figures.
3.13.4	Editorial	Updated references to other standards and figures.
3.13.6	Administrative	Replaced "Figure 2.4" with "MUTCD Part 10 Figure 7.2(b)".

Volume	Part	Section	Change type	Description of change
		3.14	Administrative	Updated extracts from TC1340 to align with most recent version.
		3.15	Administrative	Deleted extract from TC1723. Updated Figure and notes to align with content in AS1742.10.
		3.15.1	Administrative	Deleted "in Section 3.15.2 of this guide".
	2.4	4.1.8	Editorial	Replaced "MUTCD Part 9" with "AS1742.9".
	2.4	4.2	Editorial	Replaced "MUTCD Part 9" with "AS1742.9".
	2.5	5.1.2	Editorial	Corrected reference to Figure 7.1.
	2.5	5.1.4	Editorial	Replaced "MUTCD Part 7" with "AS1742.7".
	2.5	5.2	Editorial	Replaced "MUTCD Part 10" with "AS1742.10". Replaced "MUTCD Part 13" with "AS1742.13".
3		1.1	Administrative	Updated content and figures to align with MRTS45. Removed "Referenced Documents".
3		1.2	Administrative	Replaced "layout" with "design".
3		1.4	Administrative	Updated content and figures to align with MRTS45.
3		1.5	Administrative	Previously Section 1.6, shifted to match ordering of MRTS45. Updated content and figures to align with MRTS45.
3		1.6	Administrative	Previously section 1.5, shifted to match ordering of MRTS45. Replaced HOLD POINT 1 with HOLD POINT 2.
3		1.9.1	Administrative	Updated content and figures to align with MRTS45.
3		1.10.1	Administrative	Updated content and figures to align with MRTS45.
3		1.10.4	Administrative	Updated content and figures to align with MRTS45.
3		2.1	Administrative	Replaced "MUTCD Part 3 Work on Roads Section 1.5" with "Clause 7.4 of MRTS45".
3		4.2	Administrative	Deleted "and methods of sampling and testing the devices are described in Australian Standards AS 2445.3.1 to AS 2445.3.10".
3		5.2	Administrative	Updated content and figures to align with MRTS45.
4		1.1	Administrative	Deleted "Reflecting this practice, the department’s Standing Offer Arrangement for provision of road marking paint specifies only water-borne road marking paint".
4		1.2	Administrative	Updated content and figures to align with MRTS45.
4		1.3	Administrative	Updated content and figures to align with MRTS45.
4		1.4	Administrative	Amended title from "Anti-skid" to "Skid resistance for transverse line marking". Updated content and figures to align with MRTS45.
4		2.2	Administrative	Shifted reference to MRTS45 and associated content.
4		2.3	Administrative	Updated content and figures to align with MRTS45.