3Referenced documents#

Additional requirements for equipment provided under this Technical Specification are described in the referenced documents listed in Table 3.

Table 3 – Referenced documents
ReferenceTitle
AS 1319Safety signs for the occupational environment
AS 1627.0Metal finishing – Preparation and pre-treatment of surfaces, Part 0: Method selection guide
AS 1657Fixed platforms, walkways, stairways and ladders – Design, construction
and installation
AS 2578Traffic signal controllers (Withdrawn)
AS 2700Colour standards for general purposes
AS 2853Enclosures – Temperature-controlled – Performance testing and grading (Withdrawn)
AS 3990Mechanical equipment – Steelwork
AS 4070Recommended practices for protection of low-voltage electrical installations and equipment in MEN systems from transient overvoltages
AS 4100Steel structures
AS 4506Metal finishing – Thermoset powder coatings
AS 60068.2.2Environmental testing, Part 2.2: Tests – Tests B: Dry heat
AS 60068.2.78Environmental testing – Part 2.78: Tests – Test Cab: Damp heat, steady state
AS 60529Degrees of protection provided by enclosures (IP Code)
AS 61508.0Functional safety for electrical/electronic/programmable electronic safety– related systems - Functional safety and AS 61508
AS/CA S008Requirements for customer cabling products
AS/CA S009Installation requirements for customer cabling (Wiring rules)
AS IEC 62619Secondary cells and batteries containing alkaline or non-acid electrolytes – Safety requirements for secondary lithium cells and batteries, for use in industrial applications
AS/NZS 1158.3.1Lighting for roads and public spaces – Part 3.1: Pedestrian area (Category P) lighting - Performance and design requirements
AS/NZS 1170.1Structural design actions – Permanent, imposed and other actions
AS/NZS 1170.2Structural design actions – Wind actions
AS/NZS 1664Aluminium Structures
AS/NZS 1768Lightning protection
AS/NZS ISO IEC 27001Information security, cybersecurity and privacy protection – Information security management systems - Requirements
AS/NZS 3000Electrical Installation (known as the Australian / New Zealand Wiring Rules
AS/NZS 3010Electrical installations – Generating sets
AS/NZS 3012Electrical installations – Construction and demolition sites
AS/NZS 3015Electrical installations – Extra-low voltage d.c. power supplies and service earthing within public telecommunications networks
AS/NZS 3017Electrical installations – Verification guidelines
AS/NZS 3085.1Telecommunications installations – Administration of communications cabling systems, Part 1: Basic requirements
AS/NZS 3100Approval and test specification – General requirements for electrical equipment
AS/NZS 3760In-service safety inspection and testing of electrical equipment and RCDs
AS/NZS 3845Road safety barrier systems and devices
Table in words
  • AS 1319 is Safety signs for the occupational environment.
  • AS 1627.0 is Metal finishing – Preparation and pre-treatment of surfaces, Part 0: Method selection guide.
  • AS 1657 is Fixed platforms, walkways, stairways and ladders – Design, construction.
  • The reference is AS 2578 and the title is Traffic signal controllers (Withdrawn).
  • The reference is AS 2700 and the title is Colour standards for general purposes.
  • The reference is AS 2853 and the title is Enclosures – Temperature-controlled – Performance testing and grading (Withdrawn).
  • The reference is AS 3990 and the title is Mechanical equipment – Steelwork.
  • The reference is AS 4070 and the title is Recommended practices for protection of low-voltage electrical installations and equipment in MEN systems from transient overvoltages.
  • The reference is AS 4100 and the title is Steel structures.
  • The reference is AS 4506 and the title is Metal finishing – Thermoset powder coatings.
  • The reference is AS 60068.2.2 and the title is Environmental testing, Part 2.2: Tests – Tests B: Dry heat.
  • The reference is AS 60068.2.78 and the title is Environmental testing – Part 2.78: Tests – Test Cab: Damp heat, steady state.
  • The reference is AS 60529 and the title is Degrees of protection provided by enclosures (IP Code).
  • The reference is AS 61508.0 and the title is Functional safety for electrical/electronic/programmable electronic safety– related systems - Functional safety and AS 61508.
  • The reference is AS/CA S008 and the title is Requirements for customer cabling products.
  • The reference is AS/CA S009 and the title is Installation requirements for customer cabling (Wiring rules).
  • The reference is AS IEC 62619 and the title is Secondary cells and batteries containing alkaline or non-acid electrolytes – Safety requirements for secondary lithium cells and batteries, for use in industrial applications.
  • The reference is AS/NZS 1158.3.1 and the title is Lighting for roads and public spaces – Part 3.1: Pedestrian area (Category P) lighting - Performance and design requirements.
  • The reference is AS/NZS 1170.1 and the title is Structural design actions – Permanent, imposed and other actions.
  • The reference is AS/NZS 1170.2 and the title is Structural design actions – Wind actions.
  • The reference is AS/NZS 1664 and the title is Aluminium Structures.
  • The reference is AS/NZS 1768 and the title is Lightning protection.
  • The reference is AS/NZS ISO IEC 27001 and the title is Information security, cybersecurity and privacy protection – Information security management systems - Requirements.
  • The reference is AS/NZS 3000 and the title is Electrical Installation (known as the Australian / New Zealand Wiring Rules.
  • The reference is AS/NZS 3010 and the title is Electrical installations – Generating sets.
  • The reference is AS/NZS 3012 and the title is Electrical installations – Construction and demolition sites.
  • The reference is AS/NZS 3015 and the title is Electrical installations – Extra-low voltage d.c. power supplies and service earthing within public telecommunications networks.
  • The reference is AS/NZS 3017 and the title is Electrical installations – Verification guidelines.
  • The reference is AS/NZS 3085.1 and the title is Telecommunications installations – Administration of communications cabling systems, Part 1: Basic requirements.
  • The reference is AS/NZS 3100 and the title is Approval and test specification – General requirements for electrical equipment.
  • The reference is AS/NZS 3760 and the title is In-service safety inspection and testing of electrical equipment and RCDs.
  • The reference is AS/NZS 3845 and the title is Road safety barrier systems and devices.
ReferenceTitle
AS/NZS 4417Regulatory compliance mark for electrical and electronic equipment
AS/NZS 4509.1Stand-alone power systems, Part 1: Safety and installation
AS/NZS 4509.2Stand-alone power systems, Part 2: System design
AS/NZS 5139Electrical installations – Safety of battery systems for use with power conversion equipment
AS/NZS 60227.5Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V, Part 5 – Flexible cables (cords)
AS/NZS 61558.2.6Safety of transformers, reactors, power supply units and similar Part 2.6: Particular requirements for safety isolating transformers for general use
Electrical LegislationElectrical Safety Act 2002, Electricity Act 1994, and all associated Regulations and Codes of Practice
IEC 60068.1Environmental testing. Part 1: General and guidance
IEC 60884Plugs and socket outlets for household and similar purposes
IEC TR 62443Industrial communication networks – Network and system security
MASVSMobile Application Security Verification Standard – developed by the Open Web Application Security Project (OWASP)
MRTS01Introduction to Technical Specifications
MRTS50Specific Quality System Requirements
MRTS61Gantries and Support Structures for Road Signs, Tolling Systems and ITS Devices
MRTS78Fabrication of Structural Steelwork
MRTS91Conduits and Pits
MRTS93*Traffic Signals
MRTS94*Road Lighting
MRTS97Mounting Structures for Roadside Equipment
MRTS201General Equipment Requirements
MRTS202*Variable Message Signs
MRTS203*Provision of Weigh-in-Motion System
MRTS204*Vehicle Detectors
MRTS206*Provision of Variable Speed Limit and Lane Control Signs
MRTS210*Provision of Mains Power
MRTS213*UPS for Roadside Devices
MRTS218*Vehicle Activated Signs (VAS)
MRTS221*Help Phones
MRTS222*Electronic School Zone Signs
MRTS225*Imaging
MRTS226*Telecommunications Field Cabinets
MRTS227*Changeable Message Signs
MRTS228*Electrical Switchboards
MRTS229*Electronic Traffic Control Signs
MRTS231*Road Weather Monitor (RWM) Systems
MRTS232*Provision of Field Processors
MRTS233*Roadway Flood Monitoring Systems
MRTS234*Communications Cables
MRTS245*ITS Telecommunications Network (ITS TN)
MRTS250*Provision of Automatic Number Plate Recognition System
MRTS251*Motor Vehicle Traffic Counter / Classifier
MRTS255*Traffic Signal Controllers
MRTS256*Power Cables
MRTS257*Feeder Cable and Loop Cable for Vehicle Detector
MRTS259*Transportable Generator
MRTS260*Temporary Variable Speed Limit Signs
MRTS262*Temporary Variable Message Signs
MRTS263*Standalone Solar (PV) Power Systems
Queensland MUTCDManual of Uniform Traffic Control Devices (Queensland MUTCD)
SD1423Traffic Signals – Traffic Signal Controller Base Installation Details
SD1679ITS – Telecommunications Field Cabinet Base Installation Details
TRUM Vol.4 Part 3Traffic and Road Use Management Manual (TRUM) – Volume 4, Part 3: Electrical Design for Roadside Devices
TRUM Vol.4 Part 8Traffic and Road Use Management Manual (TRUM) – Volume 4, Part 8: Electrical Verification Requirements for New or Altered Roadside Installations
-Professional Engineers Act 2002
-Queensland Electrical Safety Regulation 2025

(*) Are equipment Technical Specifications that reference this Technical Specification.

Source: MRTS201 · pages 8–11 Open PDF at this page Search this document